Dilute vs Concentrate Spraying in Orchards: What Changes — remote control agricultural sprayer article

Short answer: Dilute spraying applies enough water to wet the canopy close to run-off. Concentrate spraying puts the same product per hectare into less water, for example one third of the dilute volume. Less water means fewer refills and more hectares per tank, but each droplet carries more product, so coverage, droplet size and accuracy matter more. Follow the label for any limits.

MERI tracked sprayer with a guarded airblast fan and spray lines, parked on a factory floor
MERI tracked sprayer with a guarded airblast fan and spray lines.

Two ways to carry the same dose

In dilute spraying, the volume is set to wet the trees to the point where they start to drip. The product rate is often given per 100 L of water. In concentrate spraying, the amount of product per hectare stays the same, but it is carried in less water.

The ratio between the two is called the concentration factor. If the dilute volume for a block is 1,500 L/ha and you spray it at 500 L/ha with the same product per hectare, that is a 3X concentrate.

Worked example

ItemDilute (1X)Concentrate (3X)
Water per hectare1,500 L500 L
Product per hectareSameSame
Product per 100 L of tank1 part3 parts
Hectares per 300 L tank0.2 ha0.6 ha
Refills for 3 ha155

Example figures only. Labels can set maximum concentration factors or minimum water volumes.

The refill saving is the main reason growers use concentrate sprays. On steep or distant blocks, each refill can take a long time. A smaller remote sprayer such as an ME-RCS model covers more ground per tank when the volume per hectare is lower.

Guarded airblast fan with a ring of brass nozzles on a MERI RCS sprayer
Airblast fan and nozzle ring on a MERI RCS sprayer. Lower volumes often need smaller nozzles and careful air setting.

What changes when you concentrate

  • Nozzles. Lower flow per hectare usually means smaller nozzles or faster travel. Choose nozzles for the new flow rather than lowering pressure a lot.
  • Droplets. Smaller nozzles often make finer droplets. Coverage can still be good, but drift risk rises.
  • Coverage. With less water there is no run-off to hide gaps. Every part of the canopy must be reached.
  • Accuracy. A calibration error of 10 percent now means 10 percent of a stronger mix. Calibrate carefully.
  • Weather. Fine droplets evaporate faster in hot, dry air. Check conditions before spraying.

How to switch safely

  • Check every label for limits on volume or concentration.
  • Start with the dilute volume for your trees, for example from tree row volume.
  • Choose a modest factor first and test it.
  • Select nozzles for the new flow and check pressure on a tested gauge.
  • Calibrate output with water and measure real travel speed.
  • Check coverage with water-sensitive cards before spraying the block.
MERI video: ME-RCS300-A 300 L airblast orchard sprayer.

When dilute may be better

Dilute spraying is easier to get right on large, dense trees and with older sprayers that have poor air distribution. Some products and pests also call for higher volumes. If coverage cards show gaps at a lower volume and you cannot fix them with air and speed, go back up in volume.

Example: a hillside block

A grower sprays 4 ha of hillside apples with a 300 L remote sprayer. At dilute volume, the sprayer needs many refills, each with a long climb from the filling point. Following the label limits, the grower moves to a lower volume, fits smaller nozzles, slows down slightly and checks coverage with cards. Refills drop by more than half and coverage on the cards stays even.

Common mistakes

  • Lowering volume by cutting pressure on the same nozzles.
  • Forgetting to change the product rate per tank when volume changes.
  • Skipping a coverage test after the switch.
  • Using fine sprays in hot, windy weather.

Recalculate the tank

When you change volume per hectare, the amount of product per tank changes too. Use the same formula each time: product per tank = product rate per hectare x hectares covered by one tank. Hectares per tank = tank volume divided by water volume per hectare.

Example: a 300 L tank at 500 L/ha covers 0.6 ha. If the label rate is 2 L of product per hectare, the tank needs 1.2 L of product. At 1,500 L/ha, the same tank covers 0.2 ha and needs 0.4 L. Write the numbers on the mixing sheet so the person filling the tank does not have to work them out. The MERI tank fill calculator can help check the sums.

Related MERI pages

Frequently asked questions

Does concentrate spraying use less product?

No. The product per hectare stays the same. Only the water is reduced, which saves refills and time.

What concentration factor is common?

It varies by crop, sprayer and label. Some labels set limits. Start with a modest factor and test coverage.

Is concentrate spraying suitable for a remote sprayer?

It can help a smaller tank cover more ground. Check nozzle and pump setup for the lower flow with MERI.

How do I work out the dilute volume?

Many growers use tree row volume, based on tree height, width and row spacing.

Send us your site details

Tell us the job, area, slope and country. MERI replies within 24 hours.

Ask MERI

Need a agricultural sprayer recommendation for your terrain or project?

Get a Quote
Get a Quote