Vegetation and Erosion Control at Solar Sites: Mowing Heights — remote control lawn mower article

Short answer: At solar sites, ground cover protects soil from the water that runs off panel edges. Keep vegetation short enough not to shade the panels, but not scalped; mow drainage lines and slopes with care, and repair bare patches quickly.

Why erosion happens at solar sites

Rain runs off the panels and drops along the lower edge, forming a line of concentrated flow. Bare soil there washes out, especially on slopes. Healthy grass cover holds it.

Mowing height

AreaGoalHeight
Under panelsNo shading, cover keptBelow the panel edge, not scalped
Drip linesProtect soilLeave cover; avoid scalping
Slopes and drainsHold soil, keep flowModerate height; mow when dry

General guide; follow your site plan.

Avoid making it worse

  • Do not cut so low that soil shows.
  • Avoid turning on soft or wet ground.
  • Mow slopes across or as the manual allows.
  • Keep tracks off fresh repairs.

Machines

Tracked machines spread their weight and do less damage than wheeled ones on soft ground. The T-Series (500 mm tall) works under low panels; flail mowers handle slopes and drains. MERI mowers are rated to 45°.

Repairs

Walk the site after heavy rain and note rills, bare patches and washed-out tracks. Re-seed and repair early, before the next storm and before the rainy season. Record where erosion appears and adjust mowing and drainage there.

Construction legacy

Many solar sites still have weak soil from construction. Give these areas extra cover and avoid cutting them low.

Where to look first

LocationSign of troubleFirst action
Panel drip lineA groove or line of bare soilRaise cut height; reseed
Row endsGullies where flow leaves the arrayDivert or slow water; reseed
Access tracksRuts that carry waterRepair; keep machines off when wet
Drain and swale banksSlumps, bare facesLeave taller cover; cut when dry

Mark each problem spot on the site map. Mowing crews can then raise the deck or skip the spot until it recovers.

Tracked remote mower working on a grassy hillside
A tracked remote mower working on a grassy hillside. MERI photo, not a solar site.

Setting heights by zone

Panel height sets the upper limit. Bare soil sets the lower limit. Between those two, choose the tallest height that still keeps the panels clear of shade.

The T-Series cuts 20–200 mm and is 500 mm tall, which suits low arrays. MERI flail mowers cut 30–300 mm, which gives room to leave more cover on banks and swales. Agree the target height per zone with the site owner and write it into the work order.

A post-storm routine

  • Within a few days of heavy rain, walk the drip lines and row ends.
  • Photograph each new rill or bare patch and add it to the map.
  • Hold mowing on soft areas until the ground firms up.
  • Reseed small patches by hand; report larger washouts to the site owner.
  • Check that culverts and drains are not blocked by cut grass.
Remote control mower working at a solar farm (MERI video library).

Agreeing cover targets

Agree with the site owner what good cover looks like, for example no bare strips along drip lines and full cover on swale banks.

Simple targets let crews decide on the spot whether to cut, raise the height or skip an area, and they make the inspection report easy to compare from year to year.

Common mistakes

  • Scalping along the panel edge, where flow is strongest.
  • Turning tracked machines on wet slopes, which tears the turf.
  • Leaving cuttings in swales so they block water.
  • Treating the whole site at one height, when banks need more cover than flat rows.

Writing heights into the contract

Erosion control works best when the mowing contract says what height to leave in each zone, not just how often to cut. List the zones, the minimum and maximum height for each, and what the crew should do when they find bare soil: skip, raise the deck or report. Ask for photos of problem spots after each round. This gives the site owner a record, and it gives the crew a clear rule when the ground is soft or the grass is thin.

Related MERI pages

Frequently asked questions

Why does erosion start under solar panels?

Rain runs off the panel edge and concentrates along a line.

How short should grass be under panels?

Below the panel edge, but not scalped.

Do tracked mowers help?

They spread weight and do less damage on soft ground.

When should bare patches be re-seeded?

Before the rainy season.

Send us your site details

Tell us the job, area, slope and country. MERI replies within 24 hours.

Ask MERI

Need a mower recommendation for your terrain or project?

Get a Quote
Get a Quote