Keeping Fence Rows Clean Year to Year: Mowing Cycles and Spot Treatment — remote control lawn mower article

Short answer: Fence rows fill with brush and saplings when left for a few years. Mow them on a regular cycle, cut saplings while they are small, keep the machine head clear of wire and posts, and spot treat only the problem plants where rules allow.

Why fence rows matter

Brush in the fence row damages wire and posts, hides breaks, shelters pests and spreads seed into fields. Clearing a neglected row costs far more than keeping a clean one.

A simple cycle

IntervalTask
Each seasonMow the strip beside the fence
Every 1–2 yearsCut saplings and brush in the row
As neededSpot treat or hand cut problem plants
After stormsCheck for fallen branches

Cutting near wire

Wire wraps around rotors quickly and can damage both the fence and the machine. Keep the head a safe distance from the fence and finish the last strip by hand. Mark gate posts and strainers.

Saplings

Cut saplings while they are small; once trunks thicken, a mulcher is needed and the fence may already be damaged. The ME-RFM1000 handles woody growth up to 30 cm under suitable conditions.

Machines

A flail mower suits grass and light brush along the fence; a remote tracked machine works banks and ditches beside fences where a tractor would be close to the edge. MERI tracked mowers are rated to 45°.

Wildlife

Hedgerows and fence rows give shelter to birds and insects. Cut outside nesting season and leave some sections longer where your scheme or rules require.

Spot treatment

Where allowed, spot treat resprouting stumps or invasive plants only. Follow the label and local rules.

Records

Note which rows were cut each year so the cycle stays on track.

Neglected rows

If a fence row has been left for years, clear it in stages: mulch the brush on the field side first, cut trees with an arborist where needed, repair the fence, then put the row on the regular cycle. Trying to do everything in one pass often damages the fence further.

Worked example: a boundary over two years

WhenTask
Year 1, late summerMow the grass strip on the field side of every fence
Year 1, winterCut saplings and brush on half of the rows
Year 2, late summerMow the strip again; note any new saplings
Year 2, winterCut saplings and brush on the other half
Every year, after stormsWalk the lines for fallen branches and broken wire

Example only; adjust to nesting dates and scheme rules.

Splitting the rows into halves spreads the work and always leaves some cover for wildlife.

MERI ME900-T flat-blade remote mower cutting grass between shrubs and trees
MERI ME900-T flat-blade remote mower cutting grass between shrubs and trees.

Working close to the wire

  • Walk the row first and mark loose wire, old wire on the ground and buried posts.
  • Set the machine line so the head stays clear of the fence with a margin.
  • Cut the last strip by hand with a trimmer or saw.
  • Stop at once if wire touches the head; shut down before clearing it.
  • Check the fence after each section and note repairs.

Remote control helps here: the operator can stand where the gap between head and wire is easiest to see.

Seasonal notes

Late summer and autumn suit mowing the field-side strip, after nesting and before the ground softens. Late winter suits sapling and brush work, when leaves are off and the stems are easy to see. In spring, walk the rows and plan; avoid cutting in the nesting season. After harvest, field access is often easiest for machines.

MERI mower cutting thick grass and brush (MERI video library).

Common mistakes

  • Leaving saplings until they need a chainsaw.
  • Mulching right up to the wire.
  • Cutting every row in the same year.
  • No record of which rows were done.

Gates, corners and posts

These spots collect the most growth and take the most time. Plan them on their own.

  • Corners: cut in two directions and finish the last metre by hand if the machine cannot reach.
  • Gateways: keep a wider clear strip so the gate swings freely and stock do not push through brush.
  • Strainer posts and stays: look for loose wire and rot while the area is clear.
  • Water troughs near the fence: cut around them and check the pipe is not hidden in grass.

Related MERI pages

Frequently asked questions

How often should fence rows be mowed?

The strip each season, with brush and saplings every one to two years.

How do I avoid hitting the wire?

Keep the head back and finish the last strip by hand.

When should saplings be cut?

While they are small.

What clears thicker woody growth?

A forestry mulcher.

Send us your site details

Tell us the job, area, slope and country. MERI replies within 24 hours.

Ask MERI

Need a mower recommendation for your terrain or project?

Get a Quote
Get a Quote