Molehills, Anthills and Tussocks: Mowing Lumpy Ground Without Scalping — remote control lawn mower article

Short answer: On ground with molehills, anthills and tussocks, raise the cutting height and drive slowly. Rake fresh molehills flat before the cut. Take tussocks in two passes if they are large. Cut along the bumps, not straight into them, where the site allows. Check the flails and clean soil out of the deck after the job.

Rough pasture, old parkland and road verges often have a lumpy surface. Moles push up soil. Ants build hard mounds. Coarse grasses grow into thick tussocks. A low, fast cut on this ground scalps the tops and leaves bare soil. It also blunts flails and fills the deck with dirt. This guide is for contractors, farm managers and park crews who mow this kind of ground every season.

What is under the grass

Each type of bump needs a slightly different approach. Walk the site first and note what you find.

  • Molehills. Fresh ones are soft, loose soil. Old ones settle and grass over. Both can throw soil into the deck.
  • Anthills. Often hard and dry, and they grow higher every year. A low cut shaves the top off and leaves a bare patch.
  • Tussocks. Dense clumps of coarse grass or rushes. They are tough to cut and can hide stones or holes.
  • Old ruts and hoof marks. Common in wet pasture. The tracks can drop into them and tilt the deck.

If the ground is also stony, read our guide on mowing stony pasture and rocky banks as well.

Settings for lumpy ground

MERI flail mowers have a 30–300 mm cutting height range. Manual adjustment is standard. The table below sets out a starting point. Adjust it after a short test strip.

SettingOn lumpy groundWhy
Cutting heightStart high, then lower in stepsClears the tops of mounds without scalping
Travel speedLow end of the 0–5 km/h rangeThe deck follows the ground more evenly
RouteAlong rows of bumps where possibleLess rocking and fewer deck strikes
TussocksTwo passes: high, then normalLess load on the rotor in one go

Source: MERI flail mower product pages. For the adjustment itself, see our note on cutting height adjustment.

Red MERI tracked remote mower cutting dense vegetation in a field
MERI tracked remote mower cutting dense vegetation. Recorded demonstration.

Prepare the site

  1. Walk the area. Mark large anthills, deep ruts and any holes with stakes.
  2. Rake molehills flat. Do it a few days before the cut, so the soil can settle.
  3. Remove loose stones. Mole and ant activity can bring stones to the surface.
  4. Check for wet spots. Soft ground and bumps together make the deck dig in.
  5. Cut a test strip. Mow 20–30 m, stop, and look for bare soil or torn grass.

How to cut without scalping

Scalping happens when the deck drops or tilts and the flails touch the soil. A few habits reduce it.

  • Keep the speed steady. Sudden stops and turns tip the deck.
  • Steer around large anthills, or approach them slowly and straight on.
  • Lift the cut by one step if you see bare tops after the test strip.
  • Skip very large mounds and leave them for hand tools, if the site manager agrees.
  • On slopes, follow the operating manual for direction of travel. MERI lists a 45° maximum slope, but bumps reduce grip.

Soil in the deck and flail care

Soil is harder on flails than grass. It also builds up inside the deck and adds weight to the rotor.

  • Stop and clear the deck if the cut quality drops during the job.
  • After the job, clean soil from the deck, the rotor and the tracks.
  • Look for blunt, bent or missing flails, and check the bolts.
  • Replace flails in matched sets to keep the rotor balanced.
MERI ME800-24 gasoline remote control flail mower seen from the side of the cutting deck
MERI ME800-24 flail mower, side view of the cutting deck. Product photo.

Model choice for rough pasture and parks

A narrow machine follows uneven ground more closely. The ME800-24 has an 800 mm cut and weighs 355 kg. The wider ME1000 and ME1200 models cover more area on open, flatter ground. For a fuller guide to machine choice, see choosing a mower for rough, uneven ground.

For livestock land, our farm and pasture page compares the main models. For parks and public grass, see the municipal grounds page. Ground clearance and deck options differ by configuration, so confirm them on the TDS before you order.

What to send MERI

  • Photos of the roughest part of the site, with something for scale.
  • The main type of bump: molehills, anthills, tussocks or ruts.
  • Steepest slope in degrees.
  • Grass height and number of cuts per year.
  • Yearly area, so we can suggest a spare parts pack.

Frequently asked questions

What cutting height should I use on lumpy ground?

Start high and lower it in steps until the cut is even between the bumps. MERI ME800, ME1000 and ME1200 mowers adjust from 30 to 300 mm.

Should I flatten molehills before mowing?

Yes, where you can. Rake fresh molehills flat a few days before the cut. Loose soil in the deck blunts flails and spoils the finish.

Can a remote mower cut big tussocks?

Often, yes, but take them slowly and at a higher setting. Cut very large tussocks in two passes: one high pass, then one at the normal height.

How fast should I drive on bumpy ground?

Slower than on smooth grass. MERI mowers travel at 0 to 5 km/h. Use the lower end of that range where the ground is rough.

Plan rough-ground mowing with MERI

Send photos of the site, the bump size, slope and yearly area. MERI will suggest a model, cutting tools and a quote for contractors and dealers.

Request a Mower Quote

Need a mower recommendation for your terrain or project?

Get a Quote
Get a Quote