
Short answer: Industrial sites have grass banks, fence lines, soakaways and areas under pipe racks that are awkward to mow. The ME900-T has a 900 mm flat-blade deck, a 500 mm height and a 45° slope rating on its product page, so one operator can keep these areas tidy from a safe spot.
What makes industrial grass awkward
Factories, warehouses and logistics parks have grass in the gaps: landscaped banks along the entrance, strips by the fence, swales and soakaways, verges by the car park and small areas under pipe bridges or around tanks. None of it is large, but it adds up, and much of it is on slopes.
Site managers want it neat for appearance and safety, done quickly and without contractors on foot near traffic or plant.
ME900-T product page figures
| Item | Product page figure |
|---|---|
| Engine | LONCIN 452 gasoline, 16 HP |
| Cutting width | 900 mm |
| Control system | 24 V |
| Electric power | 1,300 W |
| Blades | 2 (flat blade) |
| Cutting height | 20–200 mm (adjustable) |
| Max slope | 45° |
| Remote range | 800 m |
| Travel speed | 0–5 km/h |
| Fuel tank | 5.5 L |
| Weight | 280 kg |
| Dimensions (L×W×H) | 1450×1300×500 mm |
Data from the live MERI product page. Confirm the order configuration with MERI before you buy.
Why the ME900-T suits these sites
The flat-blade deck gives a lawn-style finish that looks right at a company entrance. At 900 mm wide it gets through the work quickly. The 500 mm height lets it pass under low pipe racks and signs where there is enough clearance. The operator stands on a footpath or behind a barrier and drives it from there.

A site plan
- Meet the site contact and get the induction and permit rules.
- Walk the areas and mark drains, valves, cable pits and sprinkler heads.
- Agree the mowing windows to avoid shift change and delivery peaks.
- Mow banks and swales first, then flat verges, then fence lines.
- Strim around signs, posts and fixtures.
- Leave the site clean: blow paths and remove clippings from drains.
Areas and approach
| Area | Approach |
|---|---|
| Entrance banks | Regular, tidy cut; change direction each visit |
| Swales and soakaways | Mow only when dry; keep inlets clear |
| Fence lines | Raise the deck near posts; strim the base |
| Under pipe racks | Check clearance against 500 mm machine height first |
| Near traffic routes | Use barriers or a lookout; stop when vehicles pass |
Follow the site traffic plan and any hazardous area rules.
Hazardous areas
Some industrial sites have zones where petrol engines are not allowed, such as areas near fuel or chemical storage. The ME900-T has a gasoline engine. Ask the site about restricted zones before the first visit and stay out of them.
A worked example
A logistics park has 2,000 m² of entrance banks, 1.5 km of fence line and four soakaways. The old routine took two people a full day with strimmers. With the ME900-T, one operator mows the banks and soakaways while the second strims posts and signs. The first visit is timed area by area. After a month, the contractor knows the real time per visit and can quote the next year with confidence.
Litter is common on industrial sites: straps, film and pallets slats. Do a quick pick before mowing. Wrapped film under the deck upsets the cut and can damage the drive.
Daily checks
- Blades tight; no wrapped straps or film.
- Tracks clean and tensioned.
- Remote stop tested at the start of the visit.
- Fuel stored and filled outside restricted areas.
Common mistakes
- Mowing soakaways when wet and leaving ruts.
- Driving under racks without checking clearance.
- Skipping the litter pick.
- Mowing near traffic routes without a barrier or lookout.
A one-page site sheet listing these points helps every operator get it right on the first visit.
Contract planning
Industrial contracts are often priced per visit. Measure the areas, split them by type, and estimate time from a first logged visit. A remote mower reduces strimming time on banks, which is usually the largest part of the hours. Keep a visit log with photos; it helps with renewals.
Related MERI pages
- ME900-T remote mower
- Remote mowers for industrial sites
- ME550-T vs ME650-T vs ME900-T
- MERI T-Series mower FAQ
- ME900-T wide flat-blade case
- Slope ratings by model
Frequently asked questions
Can the ME900-T work in hazardous zones?
It has a gasoline engine. Ask the site about restricted areas and keep the machine out of them.
Will it fit under pipe racks?
The product page lists a 500 mm height. Measure the lowest point of the rack, cable trays and supports before driving under.
How tidy is the finish?
It has a flat-blade deck with 20–200 mm cutting height, which gives a lawn-style finish suitable for entrances.
What remote range does it have?
The product page lists 800 m. On busy sites, keep the machine close and in sight.
Send us your site details
Tell us the job, area, slope and country. MERI replies within 24 hours.
Need a mower recommendation for your terrain or project?
Get a Quote