
Short answer: The ME900-T suits nut orchards that need a short, even floor before harvest and regular mowing through the season. The product page lists a 900 mm flat-blade deck, 20–200 mm cutting height, 500 mm height, 45° slope rating and a LONCIN 452 gasoline engine. Its low profile helps under low limbs.
Why the orchard floor matters in nut crops
Many almond, walnut, hazelnut and pecan growers harvest from the ground. Trees are shaken, the nuts fall, and sweepers or harvesters pick them up. A rough, tall or uneven floor hides nuts, slows the sweeper and adds trash to the load.
So the floor is mowed through the season and cut short before harvest. Large orchards use tractor-mounted mowers. On sloping blocks, under low limbs and in older orchards with tight spacing, a compact remote mower is often easier.
ME900-T product page figures
| Item | Product page figure |
|---|---|
| Engine | LONCIN 452 gasoline, 16 HP |
| Cutting width | 900 mm |
| Control system | 24 V |
| Electric power | 1,300 W |
| Blades | 2 (flat blade) |
| Cutting height | 20–200 mm (adjustable) |
| Max slope | 45° |
| Remote range | 800 m |
| Travel speed | 0–5 km/h |
| Fuel tank | 5.5 L |
| Weight | 280 kg |
| Dimensions (L×W×H) | 1450×1300×500 mm |
Data from the live MERI product page. Confirm the order configuration with MERI before you buy.
Why a flat-blade deck
Flat blades give a short, even cut on grass and soft weeds, which is what most growers want before harvest. The 20–200 mm range lets you keep a taller cover in spring and drop it low before shaking. Flat blades are less suited to heavy woody growth; a flail mower is the better tool for neglected blocks.
The machine is 500 mm high, so it can pass under many low limbs where a tractor cab would hit branches. It is 1450×1300×500 mm overall, so measure the clear width between trunks and any irrigation risers.

A season plan
| Period | Typical floor job |
|---|---|
| Spring | Higher cut to keep cover and reduce dust |
| Early summer | Regular cuts as growth slows |
| Two to three weeks before harvest | Low, even cut for sweeping |
| After harvest | Cut back growth and check for missed areas |
Starting points only. Follow your own harvest timing and orchard practice.
Many growers also mow tree rows and middles on different cycles. Plan the mower route so each pass covers the area the harvest crew will sweep.
Under the canopy
The low deck can reach closer to the trunk line than taller equipment. Keep a margin from trunks, guards and drip lines; bark damage on young trees is an entry point for disease. Finish close to trunks by hand or with herbicide, following your orchard plan.
Dust and filters
Nut orchards in dry regions are dusty, especially just before harvest. Check and clean the air filter every day in dry weather. Clean the deck underside so grass build-up does not unbalance the blades. A clean machine also throws less dust onto the trees.
A worked example
A 10 ha block has rows 6 m apart: about 16,700 m of row middle. With a 900 mm deck, a 4 m strip in each middle needs about five passes, so plan for some 80 km of travel. That is too much for one machine before harvest unless you start early. Many growers use a remote mower for slopes, edges and under-limb areas, and tractor mowers for open middles.
Common mistakes
- Cutting too low early in the season and leaving bare, dusty soil.
- Hitting irrigation risers and drip lines that were not marked.
- Driving too close to young trunks and scuffing bark.
- Waiting until the week of harvest and running out of time.
Working with the harvest crew
Agree the final pre-harvest cut date with the harvest manager. Too early, and the grass grows back before shaking. Too late, and the clippings are still on the floor when the sweeper runs. Many growers aim for a short, clean floor a week or two before the shaker arrives. Share a block map showing which rows were cut, so the crew knows where the floor is ready.
What to send MERI before ordering
- Row spacing and tree spacing.
- The lowest limb height in the rows.
- Slopes in the orchard and the steepest block.
- The area you want the remote mower to cover.
- Your harvest window and country.
MERI can then confirm whether the ME900-T, a narrower T-Series model or a flail mower suits your blocks.
Related MERI pages
- ME900-T remote mower
- Remote mowers for nut orchards
- Nut orchard floor mowing before harvest
- ME550-T vs ME650-T vs ME900-T
- ME900-T wide flat-blade case
- MERI T-Series mower FAQ
Frequently asked questions
Can the ME900-T mow under low branches?
The machine is 500 mm high on the product page, so it passes under many low limbs. Check your lowest limb height.
How short can it cut before harvest?
The deck adjusts from 20 to 200 mm, according to the product page.
What engine does it use?
The product page lists a LONCIN 452 gasoline engine, 16 HP, with a 24 V control system.
Is it suitable for overgrown blocks?
It is a flat-blade mower for grass and soft weeds. Heavy, woody growth suits a flail mower better.
Send us your site details
Tell us the job, area, slope and country. MERI replies within 24 hours.
Need a mower recommendation for your terrain or project?
Get a Quote