Flat Blade Care on T-Series Turf Mowers: Sharpening, Balance and Replacement — remote control lawn mower article

Short answer: T-Series mowers cut with two flat blades of 6 mm manganese steel. Check them daily, sharpen both blades together when the cut looks torn, check balance after sharpening, and replace both blades as a set when they are bent, cracked or worn thin.

Black MERI ME550-T flat-blade tracked mower cutting grass in a tree-lined area
MERI ME550-T flat-blade mower cutting grass.

How the T-Series cuts

The ME550-T, ME650-T and ME900-T use two flat blades instead of a flail rotor. The cutting height range is 20–200 mm. This gives a lawn-style finish on maintained grass, but flat blades show wear in the finish quickly: a dull blade tears grass tips, which turn brown a day or two later.

Daily check

  • Engine off, machine secured, as the manual says.
  • Look for nicks, bends and cracks on both blades.
  • Check the blade bolts are tight.
  • Clear grass packed under the deck.

Hitting a stone or root is the main cause of blade damage. Walk new sites before the first cut.

Sharpening and balance

Sharpen little and often: a blade that is touched up regularly keeps its shape and balance better than one ground back hard after months of use. Sharpen both blades at the same session so they cut the same way. Follow the original edge angle and remove the same amount of metal from each end. After sharpening, check the blade balances on a simple balancer or a nail through the centre hole. An unbalanced blade shakes the deck and wears the spindle.

Do not sharpen a blade that is cracked or bent. Replace it.

When to replace

  • Cracks of any size.
  • A bend you can see when the blade lies flat.
  • Wear that has thinned the tip or cut into the lift wing.
  • After a hard strike on stone or metal.

MERI supplies the straight blade set as a spare part (quote reference MERI-P20). Blades are wear parts and are not covered by the warranty.

ModelCutting widthBladesCutting height
ME550-T550 mm2 flat20–200 mm
ME650-T650 mm2 flat20–200 mm
ME900-T900 mm2 flat20–200 mm

From the T-Series TDS.

Cutting height and blade life

Cutting too low is the fastest way to wear flat blades. When the blade touches soil, it rounds the edge in minutes. Set the height so the blade clears the highest bumps on the site, and raise it on new or uneven ground. On a sports field or lawn that is cut often, small, regular height changes are better than one hard cut.

Grass length matters too. If the grass has grown long, take it down in two passes instead of one. The engine works less, the cut is cleaner and the blades stay sharp longer.

Keeping records

Write down the date of each sharpening and blade change. When you see how many hours a set lasts on your sites, you can order spare sets before the season and avoid stopping work while you wait for parts.

Common mistakes

  • Sharpening only one end.
  • Grinding until the blade turns blue, which softens the steel.
  • Refitting bolts without the correct torque.
  • Running a bent blade.

Removing and refitting the blades

Follow the operator manual for your model. The general order is the same on most flat-blade decks:

  • Stop the engine, remove the key and secure the machine on level ground.
  • Lift or tilt the machine only as the manual allows, so oil and fuel stay where they should.
  • Block the blade with a piece of wood so it cannot turn, then undo the bolt.
  • Mark which side of the blade faces down. A blade fitted upside down will not cut and can throw grass forward.
  • Clean the mounting face before refitting. Grass or rust under the blade stops it sitting flat.
  • Tighten to the torque in the manual and turn the blade by hand to check it clears the deck.
Black MERI ME550-T tracked remote control mower on a white background
MERI ME550-T tracked remote mower. Its two flat blades sit under a low deck, so keep the underside clean.

How to read the cut

What you seeLikely causeFix
Brown, torn grass tips a day laterDull bladesSharpen both blades
A ridge of uncut grass between the two blade pathsOne blade worn shorter or bentCheck both, replace as a set
Scalped patchesHeight too low for the groundRaise the cutting height
Deck vibrationUnbalanced or bent bladeBalance or replace
Clumps of grass left behindWet grass or grass too longCut when dry, take two passes

Check the blades first. Most poor finishes start there.

Walk behind the first strip of every job and look at the result. It takes one minute and tells you more than the blade itself.

Seasonal plan for a turf contractor

In spring, fit a fresh or freshly sharpened set and start at a higher height while the grass is soft and growing fast. In the main season, touch up the edges every few working days on clean turf and more often on sandy or dusty sites, because sand blunts steel quickly. In autumn, leaves hide stones and sticks, so walk the site again before cutting. At the end of the season, remove the blades, clean the spindle area and store the blades dry and oiled.

The video shows an ME550-T working on maintained turf, the kind of site where blade condition shows most in the finish.

MERI ME550-T remote control mower working on turf.

Related MERI pages

Frequently asked questions

What blades do T-Series mowers use?

Two flat blades of 6 mm manganese steel.

How do I know a blade is dull?

The grass tips look torn and turn brown after a day or two.

Can I sharpen just one blade?

Sharpen both together so they cut evenly, and check balance afterwards.

Where do I get replacement blades?

Order the straight blade set, quote reference MERI-P20.

Send us your site details

Tell us the job, area, slope and country. MERI replies within 24 hours.

Ask MERI

Need a mower recommendation for your terrain or project?

Get a Quote
Get a Quote