Flail blades

Replacement Flail Blades for Remote Control Flail Mowers

Flail blades are the fastest-wearing part on a MERI flail mower. Keep at least one full set for each common model you sell.

Fits: ME800, ME1000 and ME1200 flail mowers, gasoline and diesel, 24 V and 48 V.

  • CE Certified
  • ISO 9001
  • Exported to 100+ countries
  • Reply within 24 hours
MERI remote control mower flail blade assembly
Flail blade pair on its mounting bolt (MERI-P19).
46Common spare-part types stocked
48 hCommon parts dispatched
100+Countries exported
CECertified
ISO 9001Quality management
24 hReply time

Summary

Short answer

MERI-P19 is the flail blade, sold by the piece. MERI ME800, ME1000 and ME1200 mowers cut with flails. The number of blades depends on the cutting width.

MERI recommends one full set per common model as opening stock. A full set is 30 blades for ME800, 40 for ME1000 and 48 for ME1200.

At a glance

Part numbers, fit and check points

Part numbers and names: MERI Spare Parts Catalog (MERI-P01 to MERI-P46). Stock priority and opening quantities: MERI Recommended Spare Parts Package, per dealer location. Check points: MERI operation and maintenance notes and the operator manual. Prices are quoted per order.
Part numberPart nameFitsDealer stockCheck points
MERI-P19Flail BladeME800 (30 blades), ME1000 (40 blades), ME1200 (48 blades); gasoline and dieselPriority A (wear part); suggested opening stock 1 full set per common modelCheck after each job for missing pieces, cracks or damage. Replace damaged blades at once, even with a shallow crack.

Inspect blades after every job

Serrated MERI flail blade measured with a steel ruler before ordering replacements
Measure an old blade and send the photo with your order.
  • Remove rope, wire and debris wound on the blades and cutter shaft after each use.
  • Check for missing blades, cracks and damage after work or during stops. Replace damaged blades straight away.
  • If the cutter hits a stone or hard object, stop, switch off and inspect the blades.
  • A damaged blade upsets the balance. Vibration then loosens screws, shifts the fuel tank pads and can crack cover mounts.

Flail blades or hammer blades?

MERI flail decks can also take hammer tools by configuration. Hammer blades are a different part. See flail blades vs hammer blades and tell MERI which you run.

Before you ask for a quote

What to send MERI with your order

Machine model from the nameplate, for example ME1000D-48.

MERI part number (MERI-Pxx) and quantity.

A photo of the old part and, if you have it, the engine model and serial number.

Destination country and port, or courier address.

A photo of an old blade next to a ruler.

Questions

FAQ

How many flail blades does each MERI mower use?

ME800 models use 30, ME1000 models use 40 and ME1200 models use 48. This applies to both gasoline and diesel versions.

Should I replace blades one at a time or as a set?

Replace any damaged blade at once. MERI notes say a damaged blade upsets the balance and causes vibration, so check the whole rotor when you do.

Do T-Series mowers use flail blades?

No. The T-Series ME550-T, ME650-T and ME900-T cut with two flat blades. See the straight blade set page.

What opening stock does MERI recommend?

One full set per common model at each dealer location.

How fast does MERI ship these parts?

MERI dispatches its 46 common spare parts within 48 hours. Transit time depends on the destination and the shipping method you choose.

Keep reading

Related MERI pages

Spare parts quote or dealer stock advice

Tell MERI which flail models you sell and how many are in the field. MERI will quote blades and suggest how many sets to hold.

Need this part? Send the part number from the MERI spare parts catalog, your machine model and the serial number from the nameplate. We confirm the right part and reply within 24 hours.