
Short answer: Central reserves are long, narrow and boxed in by traffic on both sides. The key numbers are the usable width between barriers, the length of each run and where you can safely get on and off. A remote mower lets the operator stand behind the barrier or inside a coned zone while the machine cuts. Choose the machine width to fit the strip with room to spare, and use a flat-blade or flail deck to match the grass.
A central reserve, or median strip, is the grass between two carriageways. Some are a few metres wide with crash barriers on each side. Others are wide, sloped or planted. All of them sit between two lanes of moving traffic. This guide helps road contractors and councils decide where a remote mower fits.
What makes median work different
A verge has traffic on one side. A median has it on both. Crews often need closures on both carriageways, or at least the fast lane on each side. That makes every hour on the strip expensive.
Barriers add another problem. The strip may be wide enough to mow, but the gap at the ends or crossovers may be tight. The machine must get in and out without blocking a live lane.
Measure the strip first
| Measurement | Why it matters |
|---|---|
| Width between barriers | The machine needs room to turn and a margin each side |
| Entry gap or crossover width | MERI machines are 950 to 1350 mm wide (flail) or 1000 to 1300 mm (flat blade) |
| Run length | Long runs favour wider decks and fewer turns |
| Cross slope or ditch | Some reserves dip in the middle for drainage |
| Obstacles | Lighting columns, sign posts, drain covers, barrier posts |
Widths are overall machine widths from MERI product pages. Use them to check every entry point on the route.

Where the operator stands
The operator should never stand in a live lane. Common choices are a coned working zone in the closed lane or a safe spot at a crossover. On long runs, the operator walks behind the barrier line at a steady pace, keeping the machine in view.
MERI machines list 800 m standard range, up to 1,000 m with the upgraded R1 industrial remote. That range lets the operator stay back, but the real rule is a clear view of the machine. Curves, planting and barriers can block it, so plan stops to move the operator forward.
Choosing the deck and width
Most medians carry kept grass, so a flat-blade mower is a good start. The ME550-T and ME650-T are 1000 mm wide overall and 500 mm high. The ME900-T cuts 900 mm and is 1300 mm wide. See the remote turf mower page for the full range.
Rough or rarely cut medians need a flail. The ME800 flail models cut 800 mm and are 950 mm wide, which fits tighter strips. Our guide to flat blade vs flail explains the difference, and the cutting width comparison helps you balance output against fit.

Wide, sloped or planted medians
Some dual carriageways have wide central reserves with banks, ditches or shrub beds. Treat these like a small embankment site. Measure the steepest bank, check for soft ground in the ditch and mark every planted bed as a no-cut zone.
Planted medians often need a mix of machine and hand work. The remote mower takes the open grass. A crew member then trims the bed edges from inside the closure. Agree the finish standard with the client before you price it.
Job plan for a median run
- Agree closures with the road authority for both carriageways if needed.
- Check every entry gap against the machine width.
- Walk the run and remove litter, debris and stones.
- Mark lighting columns, drains and sign posts.
- Cut in long passes parallel to the barriers, with turns at the wide points.
- Trim around posts by hand from inside the closure.
- Sweep cuttings off both carriageways before reopening.
Mixed routes with verges and banks are common. See roadside vegetation mowing for verge planning, and highway embankments for steep cuttings on the same route.
What to send MERI
- Photos of the median, entry gaps and barriers.
- Strip width, run length and any cross slope.
- Grass type and the cutting height required.
- How many kilometres you cut each season.
- Number of units and destination country.
Frequently asked questions
How narrow a median can a MERI mower work in?
The narrowest models are 950 mm wide (ME800 flail) and 1000 mm wide (ME550-T and ME650-T). Leave a safe margin each side and check every entry gap.
Can the operator stand behind the barrier?
Often, yes, if they have a clear view and are not in a live lane. Follow your traffic management plan.
Flat blade or flail for medians?
Flat blade for kept grass that is cut often. Flail for rough or rarely cut strips with taller growth.
Does remote mowing remove the need for closures?
No. It reduces crew time inside the closure. The road authority still sets the traffic control.
Size a mower for your medians
Send strip widths, entry gaps and run lengths. MERI will suggest a model and quote for contractors, councils and dealers.
Need a mower recommendation for your terrain or project?
Get a Quote