Boom Height Control on Uneven Ground — remote control agricultural sprayer article

Short answer: On uneven ground, boom height changes with every bump, rut and slope, which leaves stripes of over- and under-dosing and raises drift. Keep speed down, set the boom at the nozzle maker’s height for the spray angle, choose wider-angle nozzles where suitable, keep the boom short and stable, and recheck height on each block.

Why height matters

Nozzles are designed to overlap at a set height. Too high, and spray drifts and overlaps too much. Too low, and gaps appear between nozzles. On uneven ground the boom moves up, down and sideways, so the pattern changes all the time.

What moves a boom

CauseEffect
Bumps and rutsBoom bounces up and down
Side slopeOne end drops, the other rises
Sudden turnsBoom swings forward and back
High speedAll movement gets bigger
Loose mounts and pivotsExtra play and wobble

Set the right height

Start from the nozzle maker’s chart for the spray angle and spacing. Measure from the nozzle tip to the target, which may be the ground, the weed canopy or the crop top. Check at several points along the boom, on the actual field surface, not on the yard.

Speed is the biggest control

Halving speed on rough ground cuts boom bounce a lot more than any adjustment. Pick a steady speed that keeps the boom calm, then calibrate at that speed. A remote tracked sprayer moves slowly and smoothly by design; the TDS lists 80 m/min for the MERI ME-RCS100–200 and 60–80 m/min for the ME-RCS300–500.

MERI ME-RCS200-B 200 L remote control boom sprayer.
MERI tracked sprayer tank, pump and hose assembly during a visual inspection
MERI tracked sprayer tank, pump and hose assembly during a visual inspection.

Boom length and nozzles

A short boom moves less at the tips than a long one. MERI boom versions carry 8–16 nozzles, customizable, which keeps booms compact for slopes, orchards and small fields. Wider-angle nozzles can be run lower, which reduces drift and the effect of height changes; check that the nozzle suits the product and label.

Side slopes

  • Drive up and down the slope where the crop layout allows.
  • If working across, set height at the downhill end and check the uphill end.
  • Reduce speed on cross slopes.
  • Check that tracks or wheels stay level enough for the boom to work.

Mounts and maintenance

Worn pivots, loose bolts and cracked brackets add movement. Check boom mounts weekly, replace worn bushes and keep breakaway sections working. A boom that has been knocked out of line will never hold height evenly.

Check the pattern

Spray water on a dry, flat surface or use water-sensitive paper along the boom. Look for stripes and gaps. Repeat on a typical stretch of the field. If the pattern is poor at your working speed, slow down or adjust height before spraying product.

Automatic height systems

Large field sprayers often use sensors to adjust boom height as they drive. These help on long booms and rolling fields, but they add cost and service work, and they cannot fix a boom that is driven too fast. On small farms, orchards and slopes, a short boom, a steady low speed and good setup often give an even pattern without automatic control.

A quick pre-spray routine

  • Walk the block and note ruts, ridges and side slopes.
  • Set boom height on a typical stretch of the field.
  • Check nozzle tips and filters.
  • Run water at working speed and look at the pattern.
  • Adjust speed or height, then fill with product.

Ten minutes of setup on each new block saves a re-spray or a patchy result.

Weather adds to height problems

Wind makes height errors worse because spray released higher drifts further. On uneven ground, where the boom tips rise on bumps, keep to calm conditions within the label limits and use the lowest height the nozzles allow.

Records

Note the height, nozzle, pressure and speed used for each block. If results vary across a field, the record helps find whether height, speed or ground was the cause.

Related MERI pages

Frequently asked questions

Why does boom height matter?

Nozzles overlap correctly only at the set height. Wrong height causes gaps, over-dosing and drift.

What is the best way to reduce boom bounce?

Lower the speed. It reduces boom movement more than most adjustments.

How many nozzles do MERI boom sprayers carry?

Boom versions carry 8–16 nozzles, customizable.

How should height be set on side slopes?

Set at the downhill end, check the uphill end and reduce speed.

Send us your site details

Tell us the job, area, slope and country. MERI replies within 24 hours.

Ask MERI

Need a agricultural sprayer recommendation for your terrain or project?

Get a Quote
Get a Quote