
Short answer: On uneven ground, boom height changes with every bump, rut and slope, which leaves stripes of over- and under-dosing and raises drift. Keep speed down, set the boom at the nozzle maker’s height for the spray angle, choose wider-angle nozzles where suitable, keep the boom short and stable, and recheck height on each block.
Why height matters
Nozzles are designed to overlap at a set height. Too high, and spray drifts and overlaps too much. Too low, and gaps appear between nozzles. On uneven ground the boom moves up, down and sideways, so the pattern changes all the time.
What moves a boom
| Cause | Effect |
|---|---|
| Bumps and ruts | Boom bounces up and down |
| Side slope | One end drops, the other rises |
| Sudden turns | Boom swings forward and back |
| High speed | All movement gets bigger |
| Loose mounts and pivots | Extra play and wobble |
Set the right height
Start from the nozzle maker’s chart for the spray angle and spacing. Measure from the nozzle tip to the target, which may be the ground, the weed canopy or the crop top. Check at several points along the boom, on the actual field surface, not on the yard.
Speed is the biggest control
Halving speed on rough ground cuts boom bounce a lot more than any adjustment. Pick a steady speed that keeps the boom calm, then calibrate at that speed. A remote tracked sprayer moves slowly and smoothly by design; the TDS lists 80 m/min for the MERI ME-RCS100–200 and 60–80 m/min for the ME-RCS300–500.

Boom length and nozzles
A short boom moves less at the tips than a long one. MERI boom versions carry 8–16 nozzles, customizable, which keeps booms compact for slopes, orchards and small fields. Wider-angle nozzles can be run lower, which reduces drift and the effect of height changes; check that the nozzle suits the product and label.
Side slopes
- Drive up and down the slope where the crop layout allows.
- If working across, set height at the downhill end and check the uphill end.
- Reduce speed on cross slopes.
- Check that tracks or wheels stay level enough for the boom to work.
Mounts and maintenance
Worn pivots, loose bolts and cracked brackets add movement. Check boom mounts weekly, replace worn bushes and keep breakaway sections working. A boom that has been knocked out of line will never hold height evenly.
Check the pattern
Spray water on a dry, flat surface or use water-sensitive paper along the boom. Look for stripes and gaps. Repeat on a typical stretch of the field. If the pattern is poor at your working speed, slow down or adjust height before spraying product.
Automatic height systems
Large field sprayers often use sensors to adjust boom height as they drive. These help on long booms and rolling fields, but they add cost and service work, and they cannot fix a boom that is driven too fast. On small farms, orchards and slopes, a short boom, a steady low speed and good setup often give an even pattern without automatic control.
A quick pre-spray routine
- Walk the block and note ruts, ridges and side slopes.
- Set boom height on a typical stretch of the field.
- Check nozzle tips and filters.
- Run water at working speed and look at the pattern.
- Adjust speed or height, then fill with product.
Ten minutes of setup on each new block saves a re-spray or a patchy result.
Weather adds to height problems
Wind makes height errors worse because spray released higher drifts further. On uneven ground, where the boom tips rise on bumps, keep to calm conditions within the label limits and use the lowest height the nozzles allow.
Records
Note the height, nozzle, pressure and speed used for each block. If results vary across a field, the record helps find whether height, speed or ground was the cause.
Related MERI pages
- Boom sprayer nozzle spacing and height
- Calibrating a remote boom sprayer
- Remote boom sprayer for sports turf
- ME-RCS pumps and nozzles guide
- ME-RCS sprayer FAQ
Frequently asked questions
Why does boom height matter?
Nozzles overlap correctly only at the set height. Wrong height causes gaps, over-dosing and drift.
What is the best way to reduce boom bounce?
Lower the speed. It reduces boom movement more than most adjustments.
How many nozzles do MERI boom sprayers carry?
Boom versions carry 8–16 nozzles, customizable.
How should height be set on side slopes?
Set at the downhill end, check the uphill end and reduce speed.
Send us your site details
Tell us the job, area, slope and country. MERI replies within 24 hours.
Need a agricultural sprayer recommendation for your terrain or project?
Get a Quote