Avoiding Spray Skips: Speed, Pressure and Nozzle Checks — remote control agricultural sprayer article

Short answer: Skips come from uneven speed, falling pressure, blocked or worn nozzles, wrong boom height and poor overlap between passes. Hold speed steady, check pressure at the gauge, clean nozzles, set height for proper overlap and mark the passes.

Signs of skips

Stripes of weeds or disease in rows, uneven colour after a fertiliser or foliar spray, or water-sensitive paper with gaps.

Causes

CauseFix
Speed changesHold a steady speed
Pressure dropClean filters, check pump
Blocked nozzleClean or replace
Boom too lowRaise for overlap
Missed pass lineUse markers

Speed and pressure

Rate depends on speed. Remote operation helps hold a steady pace; the ME-RCS100–200 lists 80 m/min and the ME-RCS300–500 lists 60–80 m/min (TDS). Watch the gauge for drops when the tank empties or on slopes.

Nozzle checks

  • Check each nozzle output against the average.
  • Clean with a soft brush, not wire.
  • Replace worn nozzles as a set.

Pass marking

On open ground, use foam markers or visible references. In orchards and vineyards, spray every row from the correct side.

Quick field check

After the first pass, place water-sensitive paper at a few points across the swath or canopy and run a second pass with water. Uneven spots or gaps show where to adjust height, overlap or nozzles before the real spray.

A quick diagnosis table

Pattern you seeLikely causeFirst check
Narrow stripes in line with travelBlocked or worn nozzleNozzle output test
Wide bands between passesPass spacing or boom heightOverlap and height
Patchy at the end of each tankPressure falling as the tank emptiesFilters, pump, suction
Worse on climbsSpeed or pressure change on slopesGauge on the climb
Light on one side of treesOutlets aimed wrongOutlet angle; coverage papers
Guarded airblast fan with a ring of brass nozzles on a MERI RCS sprayer
A guarded airblast fan with a ring of brass nozzles on a MERI RCS sprayer. Product photo.

Speed check in numbers

Rate falls when speed rises. If a sprayer is calibrated at 4.8 km/h and travels at 6 km/h, the rate drops by about 20%. If it slows to 3.6 km/h, the rate rises by about a third. Mark a 50 m course and time a run: km/h = 180 ÷ seconds. At 80 m/min, 50 m takes about 37.5 seconds.

A pre-spray routine

  • Clean all filters.
  • Run water and look at every nozzle pattern.
  • Check the gauge at working pressure.
  • Time a 50 m run on the field surface.
  • Set boom height or outlet angle for the crop.
  • Spray one pass with water and check papers.
A remote control orchard sprayer working in a fruit farm (MERI video library).

Weather that looks like a skip

In hot, dry weather, fine droplets can evaporate before they land, and the papers show light coverage. In wind, the pattern shifts sideways and leaves a light band on the upwind side.

Compare the weather at the time of spraying with what you see before you change the sprayer, and keep within the label wind and temperature limits.

Common mistakes

  • Speeding up to finish before rain.
  • Replacing only the one nozzle that failed when the rest are worn.
  • Not watching the gauge as the tank empties.
  • Skipping alternate rows in orchards when the label calls for both sides.

Spraying on slopes

On slopes, pressure and speed change on the climb and on the way down, and the tank level shifts. Watch the gauge on the first climb and compare it with the flat. If pressure drops on climbs, check the suction filter and the tank level before blaming the pump. Plan the passes so the sprayer works along the contour where the manual allows, and keep a small reserve in the tank so the pump does not draw air on steep ground.

With a remote sprayer the operator can walk beside the work and watch the spray pattern directly.

After the spray

Look at the result a week or so later. Stripes or patches that line up with passes point to the sprayer, not the product. Note where they are and check that section of the boom or those outlets before the next spray.

Related MERI pages

Frequently asked questions

What causes spray skips?

Uneven speed, pressure drops, blocked nozzles, wrong height and poor overlap.

How do I clean a nozzle?

With a soft brush, not a wire.

Does speed affect the rate?

Yes, faster travel gives a lower rate.

How fast do ME-RCS sprayers travel?

80 m/min on ME-RCS100–200; 60–80 m/min on ME-RCS300–500 (TDS).

Send us your site details

Tell us the job, area, slope and country. MERI replies within 24 hours.

Ask MERI

Need a agricultural sprayer recommendation for your terrain or project?

Get a Quote
Get a Quote