Bowling Green Banks and Ditches: Mowing the Steep Surround Without Damaging the Green — remote control lawn mower article

Short answer: The banks around a bowling green are short, steep and tight against the ditch. Mow them across their short length with a compact machine that cannot drop into the ditch, keep the cut even with the surrounding lawns, and finish the bank edge by hand. Never drive on or turn on the green itself.

Why the banks take so long

Groundsmanship magazines spend most of their bowls coverage on the green itself: cutting heights, top dressing, renovation. The banks get less attention but take a lot of the weekly time. They are steep, narrow and run all the way round the green, with a ditch at the bottom and often a path or seating at the top.

Most clubs strim them or use a small hover mower on a rope. Both are slow and tiring, and volunteers do much of the work.

Know the layout

FeatureWhat to noteEffect on mowing
DitchWidth, depth, edge boardsMachine must stay clear of the drop
BankHeight and steepnessDecides machine or hand work
Top of bankPath, seats, fencesTurning space and standing position
CornersTight radiusUsually hand finish
Green edgeSeparate surfaceNo machine contact

Each green is different. Measure before choosing a method.

A safe mowing pattern

Mow the bank from the top path, with the machine working along the bank face and the operator standing on the path. Keep the tracks well above the ditch edge. A compact tracked remote mower lets the operator stand back on firm ground and stop the machine at once if anything looks wrong. Tight corners and the edge strip next to the ditch are best done by hand.

  • Walk the bank and remove fallen jacks, mats and litter.
  • Mow the bank top first to set a clean line.
  • Work the face in short, steady passes.
  • Hand finish corners and the ditch edge.
  • Blow clippings off paths, away from the green.

Machine choice

For small surrounds, the flat-blade T-Series gives a neat finish: it cuts 20–200 mm and the machine is 500 mm high. The ME550-T measures 1100×1000×500 mm. MERI tracked models are rated to 45°, but bowling banks are short and the real limit is space at the top and the drop to the ditch. Measure both before you decide.

MERI ME900-T flat-blade remote mower cutting grass between shrubs and trees
MERI ME900-T flat-blade remote mower cutting grass between shrubs and trees.
MERI 45° slope climbing test.

Timing around play

Cut banks on a non-match day, ideally the day before the green is cut, so clippings never blow onto the playing surface. In wet weather, leave the banks: a slip at the top could send a machine toward the ditch, and soft turf tears. Agree a weekly slot with the club so the job no longer depends on who is free.

Volunteers and safety

Many bowls clubs rely on older volunteers for grounds work. Taking them off the bank face reduces the risk of slips and strains. A remote machine still needs training: the operator should know how to stop it, keep it in view and never stand below it on the bank. Standard remote range is 800 m, far more than any green needs, and the machine stops if the signal is lost.

Common mistakes

  • Letting the machine get too close to the ditch edge.
  • Cutting banks on a match day and blowing clippings onto the green.
  • Mowing wet banks and tearing the turf at the top edge.
  • Turning on the green surround instead of the path.

Estimating the time

Measure the bank length round the green and the slant height of the face. A green with 160 m of bank and a 1 m face is about 160 m² of slope, plus corners. Time one side, then scale up. Add the hand finishing at corners and the ditch edge. Many clubs find the machine turns a long strimming session into a short weekly job.

Related MERI pages

Frequently asked questions

Can a remote mower cut bowling green banks?

Often yes, if there is space at the top and the machine can stay well above the ditch. Measure the bank and the top path first.

Which MERI mower suits small green surrounds?

A compact flat-blade T-Series model such as the ME550-T, which measures 1100×1000×500 mm and cuts 20–200 mm.

When should bowling banks be mown?

On a non-match day, ideally before the green is cut, so clippings never land on the playing surface.

What still needs hand work?

Tight corners, the ditch edge and any area next to seating or fences.

Send us your site details

Tell us the job, area, slope and country. MERI replies within 24 hours.

Ask MERI

Need a mower recommendation for your terrain or project?

Get a Quote
Get a Quote