
Two properties with the same acreage can require very different mowing work. A useful quote identifies the acres to cut each visit, the grade and condition of each work zone, and the edges or obstacles that need separate treatment.
Describe the finish you want and the conditions that trigger reassessment. Compare bids on the same mapped scope and visit frequency.
Draw the scope before requesting the rate
A comparable commercial slope mowing quote starts with a map of what gets cut at each visit. Include level sections, banks, narrow transitions and areas that require handwork or a separate method. Write down the number of visits and what the customer will accept as finished. Keep area, frequency and finish together on the quote. Otherwise two providers can look far apart on price while quoting substantially different work.
Use one drawing and a short zone sheet. For each zone record measured area, surface, vegetation, route in and out, and anything that makes the work conditional. Have the contractor walk the site and verify that measurement and boundaries. If part of the slope cannot be assessed from the drawing, flag it as pending. Include a named contact who can approve a change rather than allowing assumptions to become part of the price.
Use model dimensions to test the access assumptions
A proposal can identify its intended equipment before the customer agrees to the service. The two MERI standard gasoline configurations below illustrate why a wider cutter can change which blocks belong in the machine scope. The TDS gives the nominal cut and the overall machine width separately. These dimensions help screen access. They do not establish the acceptable working grade, a towing plan or site productivity.
| Standard TDS item | ME800-24 | ME1200-24 |
|---|---|---|
| Cutting width | 800 mm | 1200 mm |
| Overall width | 950 mm | 1350 mm |
| Net weight | 355 kg | 386 kg |
| Gasoline engine | Loncin 459, 18 hp | Loncin 459, 18 hp |

Write a zone sheet a contractor can price
Start with what the customer can verify. For routine grass, specify the area, visit frequency, finish and how the contractor should report skipped sections. On a bank, add the measured angle or grade, the measurement convention, surface condition and access. State who is responsible for clearing litter or moving obstructions before work. Identify areas beside public paths, fences, drains or protected vegetation that the contractor must treat separately or exclude. A public contract can use measured acres per mowing cycle with separate provisions for access or finish. Your own quote should use the measures and conditions applicable to the property.
Take two illustrative properties with equal area. The first has several open banks connected by a wide service lane. The second has a similar total area divided by narrow gates, a soft transition and a strip behind a fence. The second property can require more mobilization, transfers and handwork even if the same nominal machine fits some of the acreage. Ask each bidder to separate the regular machine work from those items and to show any equipment change in the zone sheet. That makes it easier to compare price and to assign responsibility if an area is inaccessible on the day.
Separate price units, visit assumptions and acceptance
- Routine machine work: include the named zones and the measured area per visit. State the visit count and expected finish.
- Transitions and separate work: identify turning space, transfers, restricted edges and any handwork. Ask for the unit or allowance used in the quote.
- Mobilization: specify the access window, loading location and whether return visits are included.
- Reassessment: describe when wet ground, access changes or growth outside the stated scope triggers review and who approves revised work.
- Acceptance: agree how the crew records completed areas, exceptions and requested follow-up.
Keep the commercial assumptions visible. A quote with fewer visits can be less expensive but still miss the customer’s required frequency. A quote that includes every mapped edge can appear more expensive than one that leaves handwork to the property team. Ask for a revised comparison on matching scope before assigning value to either difference. The same discipline helps a dealer explain whether a second configuration or outside support is appropriate.
Ask for proof tied to the proposed job
Request the specification sheet for the exact model and cutter. Compare its transport and working envelopes with the limiting opening and planned maneuver area. If the proposed job depends on a particular finish or dense growth, schedule an approved, representative demo and agree what the evidence should show. Equipment ratings and video examples support a configuration review. The site survey, model manual and customer’s scope establish the work the contractor can quote.
Use the MERI mower demo checklist to plan the test, and compare the ME800-24 and ME1200-24 product references before requesting the final fitted dimensions.
Buyer FAQ
Should two contractors quote the same rate unit?
Have them identify their units and what each includes. Per-visit and per-area rates can be compared once the mapped area, frequency, mobilization and exclusions are aligned.
Can a cutting-width figure tell me whether a machine fits the route?
Use outside dimensions with the fitted equipment, gate hardware and maneuvering area. Cutting width tells you how wide a nominal pass is.
How do I handle a bank that is too wet on the scheduled day?
Agree a reassessment and reporting process in advance. Record the area held and arrange any change through the named scope approver.
Request a commercial configuration quote for the mapped site
Send your job sketch, operating conditions and expected order size. MERI can compare the fitted configurations and prepare a written quotation.
Need a mower recommendation for your terrain or project?
Get a Quote