ME-RFM1000-E · Design details

ME-RFM1000-E Design Details: 12 Engineering Features Up Close

This is the battery-electric MERI forestry mulcher, part by part. Here is what is inside the rotor, the cooling, the tracks and the frame, and what each part does on site.

  • CE Certified
  • ISO 9001
  • Reply within 24 hours

MERI ME-RFM1000-E battery-electric remote control forestry mulcher
30 kWhLiFePO4 battery
9 kWWater-cooled cutter motor
1,000 mmWorking width
200 mRemote range
≈7 hOperating time

At a glance

12 details buyers ask about

Tap any part to jump to the close-up and what it means for your crew.

Chapter 1

Cutting system

How the rotor bites, and why it stays out of trouble

ME-RFM1000-E rotor with fixed teeth in a double-spiral layout
Teeth set in a double spiral around the rotor
01Lower peak load

Double-spiral tooth layout

The teeth sit in a double spiral around the rotor. At any cross-section, only two teeth cut at the same time.

Fewer teeth in the wood at once means a lower peak load on the cutter motor. In MERI's side-by-side demo, the 9 kW ME-RFM1000-E matched a layout that needed 18 kW for the same job.

That demo is a comparison, not a rule. Real results change with wood type, size and moisture.

  • 2 teeth per cross-section
  • 9 kW cutter motor
  • 3,450 r/min rotor
ME-RFM1000-E mulching rotor with crescent depth limiters beside each tooth
Each limiter sits about 1 cm below the cutting edge
02Controls the bite

Crescent depth limiter

A crescent-shaped limiter sits beside each tooth. Its highest point is about 1 cm below the cutting edge.

When the rotor meets a trunk, the limiter touches first. Each tooth can then bite only about 1 cm deep per pass. The rotor does not grab a big chunk and stall.

Three stress-relief holes in each limiter spread impact loads, so cracks are less likely to start at one point.

  • ≈1 cm max bite per tooth
  • 3 stress-relief holes
Four-sided fixed mulcher teeth used on the ME-RFM1000-E rotor
One tooth, four usable cutting faces
03More hours per set

Four-sided teeth

Every tooth has four usable cutting faces. When one face wears, loosen the bolt and turn the tooth to a fresh face.

Turn it to the opposite face first. One set of teeth lasts longer, and your crew carries fewer spares to site.

  • 4 cutting faces
  • Bolt-on, turn in the field
Anti-wrap plate guarding the ME-RFM1000-E rotor bearing end
MERI's own anti-wrap plate at the rotor end
04Protects the bearings

Anti-wrap plate

Old orchards and farm land hide wire and drip-irrigation tape. If it winds onto the rotor shaft, it can wreck a bearing.

MERI designed its own anti-wrap plate for the rotor ends. It blocks wire and tape from winding in, which cuts the risk of bearing damage.

  • MERI in-house design
  • Stops wire and drip tape

Chapter 2

Cooling and power

Keeping a 9 kW motor and a 30 kWh battery working

ME-RFM1000-E 9 kW cutter motor with liquid-cooling water channel and air vents
9 kW cutter motor with a spiral water channel
Crescent air inlet on the ME-RFM1000-E cutter motor housing
Crescent air inlet on the motor housing
05Two cooling paths

Liquid and air cooling for the cutter motor

The 9 kW cutter motor is cooled two ways at once.

Coolant flows through a spiral channel in the motor housing, from inlet to outlet, and carries heat away.

A small fan pulls air in through crescent-shaped vents and out the other side. Two cooling paths keep heat moving out of the motor on long shifts.

  • 9,000 W cutter motor
  • Spiral water channel
  • Fan + crescent vents

Visible spinning impeller coolant flow indicator from the ME-RFM1000-E cooling loop
If the impeller spins, coolant is flowing
06Check at a glance

Coolant flow indicator

A clear window with a small impeller sits in the coolant line.

If the impeller spins, coolant is flowing and the pump is working. Your operator can check it in a second, before and during work. There is no need to trace hoses.

  • Visible impeller
  • Pump check in seconds
Two covered charging ports and power switch on the ME-RFM1000-E battery body
Two covered ports with Anderson connectors
075.4 kW charging

Dual charging ports

The battery body has two charging ports with Anderson connectors. You can run two chargers at the same time.

Each charger is 2.7 kW, so two give 5.4 kW in total. That puts about 5.4 kWh into the 30 kWh LiFePO4 battery each hour.

  • 2 × 2.7 kW chargers
  • 5.4 kW total
  • Anderson connectors

Site power check: plug each charger into its own outlet rated for its load. Two outlets do not always mean two separate circuits. The upstream circuit, outlets and cables must carry the full 5.4 kW (the demo used 6 mm² supply cable). Ask a qualified electrician to check your site supply.

Chapter 3

Chassis and tracks

Frame, tracks and drive built for rough ground

10 mm thick 510 high-strength steel idler bracket on the ME-RFM1000-E track frame
10 mm local plate in 510 high-strength steel
Split dual-disc front idler on the ME-RFM1000-E rubber track
Split dual-disc idler turns each side freely
Outer-rotor planetary travel reducer bolted to the ME-RFM1000-E drive sprocket
MERI outer-rotor planetary travel drive
08Stable on rough ground

510 steel frame and track system

The frame is 510 high-strength steel, thickened where the loads are high. Frame plate is 6 mm. Local plates, such as the idler bracket, are 10 mm.

A long track footprint and a shifted pivot point reduce nose-diving on rough ground.

The front idler uses two separate discs. Each disc turns on its own, so the track turns with less binding.

Each track is driven by MERI's own outer-rotor planetary reducer, built for travel torque and climbing.

  • 510 high-strength steel
  • 6 mm frame / 10 mm local plate
  • 45° climbing / 35° working
Custom-moulded drive sprocket and travel drive hub on the ME-RFM1000-E
Drive sprocket made from MERI's own mould
09MERI's own tooling

Custom-moulded drive sprocket

The drive sprocket is MERI's own design, made from a custom mould for this machine.

If you stock spares for your customers, ask MERI for the sprocket part number with your order.

  • Custom mould
  • MERI in-house design
160 mm ME-RFM1000-E road roller with outer guard sleeve and bracket
160 mm roller with outer guard sleeve
10Built for mud

160 mm rollers with double seals

Road rollers and carrier rollers are 160 mm in diameter. They run on imported 6205 bearings.

Each roller has two layers of protection: an oil seal, plus an outer sleeve over it. The sleeve keeps mud and water off the seal and bearing on wet sites.

  • 160 mm rollers
  • 6205 bearings
  • Oil seal + outer sleeve

Chapter 4

Lifting and protection

Taking hits, and moving between sites

ME-RFM1000-E thickened lift arm with stress-relief holes beside the hydraulic cylinder
Thickened parallel lift arm with stress-relief holes
11Protects the cylinder

Lift arm takes the impact

When the head is low and hits something head-on, the thickened parallel lift arm takes the load.

The force goes through the arm into the frame, not straight into the hydraulic cylinder. Stress-relief holes along the arm help spread the load and protect the cylinder.

  • Thickened parallel arm
  • Stress-relief holes
  • 0–400 mm cutter lift
Lifting lug welded to the ME-RFM1000-E side frame for crane loading
One of four lifting lugs, two per side
12Easy loading

Four lifting lugs

Four lifting lugs sit on the sides of the machine, two on each side.

Your crew can crane the 882 kg machine on and off a truck level and under control, for delivery, unloading and site moves.

  • 4 lugs
  • 882 kg net weight

Questions

Frequently asked questions

What cutter motor does the ME-RFM1000-E use?

A 9,000 W (9 kW) cutter motor. It is cooled by liquid through a spiral water channel and by air through crescent vents with a small fan.

How fast can it charge?

It has two charging ports. Two 2.7 kW chargers can run at once for 5.4 kW in total. The TDS lists about 6 h fast charging or 12 h standard charging. Your site supply must carry the full charging load.

How do I get more life from the teeth?

Each tooth has four cutting faces. When one face wears, loosen the bolt and turn the tooth, starting with the opposite face.

What bearings are in the track rollers?

The 160 mm road and carrier rollers run on imported 6205 bearings, protected by an oil seal plus an outer sleeve.

Keep reading

Related MERI resources

For dealers and fleet buyers

Stocking the ME-RFM1000-E?

Send your market, quantity and site type. Ask about price, MOQ and lead time. We reply within 24 hours.