Mowing Hillside Solar Farms: Rows, Banks and Drainage Swales — remote control lawn mower article

Short answer: On hillside solar farms, the hard parts are the steep banks, the drainage swales and the ground under the panels. Tractors stay off slopes like these, and brushcutter crews tire fast on them. A remote tracked machine lets the operator stand on flat ground while the machine works the slope. Choose the machine by three numbers: the lowest panel edge, the steepest slope and how tall the grass gets between visits.

45°slope rating, ME900-T and ME1000D-48
500 mmME900-T height for low panels
35°ME-RFM1000-E maximum operating angle
3 numberspanel edge, steepest slope, grass height

More solar farms are now built on hills, old farmland terraces and mountain sides. The panels follow the ground, so mowing does too. That makes vegetation work slower and riskier than on a flat site. This guide is for solar O&M teams and contractors who look after sloped arrays.

Why hillside arrays are harder to mow

  • Rows follow the terrain, so the gap under the panels changes along each row.
  • Cut banks and fills sit between terraces. Some are steeper than the rows.
  • Drainage swales and channels run downhill and must stay open.
  • Loose stones and gravel tracks are common, which raises the debris risk.
  • Brushcutter work on a slope is slow and tiring. Ride-on mowers and tractors risk rolling over.
Yellow MERI electric tracked mulcher working across a grassy slope below a row of solar panels
MERI electric tracked mulcher on a sloped solar farm.

Measure before you choose

What to measureHowWhy it matters
Lowest panel edgeOn the downhill side of each table, at several rowsSets the maximum machine height
Steepest slopeSlope gauge or phone app on banks and rowsMust stay inside the machine’s rated slope
Clear lane widthBetween piles, cable trays and fencesSets machine width and turning room
Swales and channelsWidth, depth and whether they hold waterDecides where tracks can cross
Grass height between visitsMeasure before a planned cutFlat blades or flails, and how often to mow

Match the machine to the site

ItemME900-TME1000D-48ME-RFM1000-E
TypeLow-profile flat-blade mowerDiesel flail mowerElectric mulcher
Machine height500 mm920 mm640 mm
Cutting width900 mm1,000 mm1,000 mm
Cutting height20–200 mm30–300 mm0–400 mm lift range
Slope rating45°45°35° maximum operating angle
Best use on a hill siteShort, kept grass under low panelsTaller grass on banks and in higher rowsWoody growth and heavy weeds

Figures come from the ME900-T solar guide, the ME1000D-48 product page and the ME-RFM1000-E data sheet. Many hill sites need two machines: a low unit for the rows and a flail mower for the banks.

How to work a slope safely

  1. Walk the area first. Mark holes, rocks, cables and soft patches.
  2. Use the travel direction the manual allows. Do not exceed the rated slope, and treat it as a limit, not a target.
  3. Avoid sharp turns across the slope. Turn on flatter ground at the ends of rows.
  4. Stand above or beside the machine, never below it. Keep the machine and the cutting area in sight.
  5. Slow down on gravel and wet grass. Tracks grip better, but they can still slide.

Drainage swales and erosion

On a hillside, the grass cover holds the soil. Cutting too low on a steep bank can open it up to erosion. Set a higher cutting height on erosion-prone faces. Keep the lower height for flat rows where shading is the main concern.

Mow swales when they are dry. Soft, wet channels leave ruts that carry water and soil. Clear blocked culvert mouths by hand. For long channels, see our page on remote mowers for drainage ditches.

MERI diesel tracked mulcher cutting grass beside a concrete drainage channel between solar panel rows
MERI diesel tracked mulcher beside a drainage channel on a solar farm.
  • Stones and the panels: hill sites often have loose stones at the surface, and a flail or mulcher can throw them. Plan the cutting direction away from the modules and check the guards. See checking debris exposure around panels.
  • What it costs: on slopes, brushcutter crews slow down a lot, so the gap between manual and remote work is often wider than on flat ground. Use our solar farm mowing cost calculator with your own crew output.

What to send MERI

  • Photos of a typical row and the steepest bank.
  • Lowest panel edge height and clear lane width.
  • Steepest slope in degrees.
  • Size and condition of drainage swales.
  • Site area and number of cuts per year.

Frequently asked questions

What slope can a remote mower handle on a solar farm?

The ME900-T and ME1000D-48 are rated to 45°. The ME-RFM1000-E lists a 35° maximum operating angle. Ground conditions often set a lower practical limit, so walk the site first.

Can one machine do both the rows and the banks?

Sometimes. If the lowest panel edge is above 920 mm, the ME1000D-48 can do both. On lower arrays, pair a low ME900-T for the rows with a flail mower for the banks.

Should we mow drainage swales?

Yes, when they are dry. Keep some grass cover to hold the soil, and avoid soft ground that the tracks would rut.

Diesel, gasoline or electric on a hill site?

Fuel is often easier to bring in than charging power on remote hill sites. Electric needs a charging plan. MERI does not recommend its diesel models for the USA.

Plan mowing for your hillside array

Send MERI your slopes, panel heights and lane widths. We will suggest the right machine mix and send the TDS for your quote.

Request a solar farm quote

Need a mower recommendation for your terrain or project?

Get a Quote
Get a Quote