Marestail and Fleabane on Field Margins: Mowing as Part of Resistance Management — remote control lawn mower article

Short answer: Marestail and fleabane spread huge numbers of wind-blown seeds from margins, ditches and roadsides into fields. Mowing margins before the plants flower, and again on regrowth, cuts the seed supply and supports a programme that uses more than one control method.

Why margins matter

These weeds thrive on undisturbed ground: field edges, ditch banks, fence lines and verges. Seed blows into fields from there.

Timing

  • Cut before flowering and seed set.
  • Watch for regrowth from cut stems.
  • Repeat cuts through the season.
  • Keep cutting height low enough to remove the growing tips where practical.

Combining methods

MethodRole
Mowing marginsCut seed supply
Crop competitionShade out seedlings
Tillage where allowedBury seed
Different herbicide groupsFollow local advice

Ask a local agronomist for the programme.

Machines

Margins and ditch banks are often steep or soft. A tracked remote flail mower cuts them without a tractor near the edge. MERI tracked mowers are rated to 45° and flail models cut 30–300 mm.

Hygiene

Clean machines before moving from infested margins to clean fields.

Records

Map infested margins and note cutting dates. Patches that shrink show the plan works.

Where the seed comes from

A single plant can produce very large numbers of light seeds that travel long distances on the wind. Uncut verges, railway banks and neighbouring fields can all be sources. Work with neighbours and road managers where possible, because one uncut margin can reseed many fields.

Practical cutting plan

TimeTask
Early summerFirst cut of margins before bolting plants flower
MidsummerCheck regrowth; second cut
Late summerCut any plants that escaped
After harvestCheck stubble and margins

Adjust to local growth timing.

Mapping margins step by step

  • Walk or drive the farm boundary in late spring.
  • Mark each infested margin on a phone map with a photo.
  • Rate each patch: scattered, moderate or dense.
  • Note the ground: flat, bank, ditch side or verge.
  • Choose the machine for each patch from the ground type.
  • Repeat the walk each year and compare.
MERI ME1200-48 gasoline remote control flail mower, front view
MERI ME1200-48 gasoline remote control flail mower, front view (product photo).

Cutting height and regrowth

These weeds often send up side shoots after a cut, especially if the cut leaves a tall stub with buds. Cut low enough to take the main stem well below the first side branches where the ground allows, and check again two to three weeks later. On banks with stones, a slightly higher cut protects the blades; plan a second cut sooner instead.

Common mistakes

  • Cutting after flowering, when seed is already set.
  • One cut and no check for regrowth.
  • Moving from infested margins to clean fields without cleaning the machine.
  • Ignoring ditch banks because they are hard to reach.
MERI mower cutting thick grass and brush (MERI video library).

Machine by margin type

MarginSuggested machine
Flat grass strip beside a fieldTractor mower or remote flail mower
Ditch bankRemote tracked flail mower
Steep verge or bankRemote tracked mower; MERI tracked mowers are rated to 45°
Fence line with postsRemote mower plus hand work at posts

Seasonal notes

Plants that emerge in autumn overwinter as rosettes and bolt early the next year, so an early summer check catches them before flowering. Spring-emerging plants bolt later, which is why a midsummer and a late-summer check are both worth doing. After harvest, look along the margins and in stubble for plants that escaped.

Know the stages on the margin

Both weeds are easier to manage at some stages than others. Walk the margins and note which stage you see.

  • Rosette: small, flat plants close to the ground, common after autumn or spring germination.
  • Bolting: an upright stem starts to grow from the rosette.
  • Flowering and seed: small heads form; seed is light and travels on the wind.

Cutting before seed set is the main aim. A plant cut late, with ripe seed, can still spread it.

Margins next to roads and neighbours

Seed blows across boundaries. Where a margin borders a road verge or a neighbour’s field, talk to the owner and try to time cuts together.

Related MERI pages

Frequently asked questions

Why mow field margins for marestail?

To stop seed blowing into fields.

When should margins be mowed?

Before flowering, and again on regrowth.

Is mowing enough alone?

No, combine it with other methods.

Which mower works ditch banks?

A tracked remote flail mower.

Send us your site details

Tell us the job, area, slope and country. MERI replies within 24 hours.

Ask MERI

Need a mower recommendation for your terrain or project?

Get a Quote
Get a Quote