Smart and Variable-Rate Sprayers in Vineyards — remote control agricultural sprayer article

Short answer: Variable-rate sprayers adjust output to the canopy using sensors, so less product lands on gaps and small vines. Before investing, get the basics right: canopy-matched volume, outlets off at gaps and row ends, good calibration and records.

What they do

Sensors detect canopy size or gaps and change flow or switch nozzles. The aim is the same dose per unit of canopy, with less waste.

Before buying

  • Is your canopy variable enough to gain?
  • Can your dealer support the sensors and software?
  • How is it calibrated and checked?
  • What records does it produce?

Basics first

StepEffect
CalibrateCorrect rate
Match volume to growth stageLess over-spray early
Turn off at gaps and row endsLess waste
Aim outlets at the canopyBetter coverage

Standard remote sprayers

MERI ME-RCS airblast sprayers are remote-controlled tracked carriers with 100–800 L tanks. They do not list sensor-based variable rate; the operator controls spraying and can stop at row ends, staying out of the spray cloud.

Check coverage

Water-sensitive paper in the canopy shows whether any system, smart or standard, puts spray where it should.

What growers report

Growers who adopt canopy-sensing sprayers usually see the biggest savings early in the season, when canopies are small and gaps are many. Later, with full canopies, the difference narrows. The result depends on vine spacing, training system and how well the standard sprayer was set up before.

Questions for the dealer

  • How does the system detect canopy, and how is it checked?
  • What happens if a sensor fails during spraying?
  • Can it be fitted to my sprayer or only to new machines?
  • What training and support are included?
  • What records can it export for compliance?

Worked example: where the savings come from

Early in the season, young shoots fill only part of the canopy space, and there are gaps at missing vines. Later, the canopy fills in. A sprayer that sprays the full canopy volume all season wastes the most product early on.

StageCanopyWaste with a fixed settingSimple fix without sensors
EarlySmall, many gapsHighFewer outlets, lower volume, outlets off at gaps
MidFillingMediumAdjust volume to canopy height
FullDense wallLowFull outlets, matched air

Many of the early savings can be made with careful manual settings. Sensors make them automatic and more consistent.

Getting a standard remote sprayer close to the target

  • Calibrate at the start of the season and after any nozzle change.
  • Set outlets by canopy height at each growth stage.
  • Switch off at row ends and over missing vines.
  • Hold a steady speed: 80 m/min on the ME-RCS100–200, 60–80 m/min on the ME-RCS300–500 (TDS).
  • Check coverage with water-sensitive paper after each change.
MERI tracked sprayer with a guarded airblast fan and spray lines, parked on a factory floor
A MERI tracked sprayer with a guarded airblast fan and spray lines, parked on a factory floor. Product photo.
A remote control vineyard sprayer (MERI video library).

Deciding whether to invest

Compare three things: how variable your canopy is, how much product you use per season, and how much support your dealer can give for the sensors. If the vineyard is uniform and the standard sprayer is already well set up, the gain may be small. If blocks are patchy, young or replanted, the gain is larger.

Training the operator

A smart sprayer still needs a trained operator. Show them how to check the sensors at the start of the day, what the system shows when a sensor is blocked and how to switch to manual if it fails.

Keep a short checklist with the machine, and note any sensor fault in the spray record so the dealer can see the pattern.

Common mistakes

  • Buying sensors before calibrating the sprayer.
  • Not checking coverage after the system is fitted.
  • Expecting the same saving in full canopy as at early growth.
  • No plan for what to do if a sensor fails mid-spray.

Records that prove the saving

Whether you use sensors or careful manual settings, record the volume used per block at each spray and the coverage check result. Compare season totals block by block. If a new system is fitted, keep one season of records before and after, on the same blocks, so you can see the real saving and not just the figure in the brochure.

Related MERI pages

Frequently asked questions

What is a variable-rate sprayer?

One that adjusts output to the canopy using sensors.

Do ME-RCS sprayers have variable rate?

They do not list sensor-based variable rate.

What should I do before buying one?

Calibrate, match volume to growth stage and check coverage.

How do I check coverage?

With water-sensitive paper.

Send us your site details

Tell us the job, area, slope and country. MERI replies within 24 hours.

Ask MERI

Need a agricultural sprayer recommendation for your terrain or project?

Get a Quote
Get a Quote