How to Check Remote Mower Visibility Across a Convex Slope — remote control lawn mower article

Walk the route with the site team and mark where the crest blocks the view of the mower, the cutting area or people entering the work zone. Ask the supplier to check sightlines from approved operator positions. Include those positions in the procurement brief and demonstrate the route under approved conditions. If the operator loses the required view, have the site team approve a revised route or plan separate maintenance for that section.

Draw the crest and the operator positions

Start with a map of the work area. Mark the crest, the proposed passes on each side, the approaches and any access routes that people share with the crew. Then mark the places where the site team permits an operator to stand. Confirm those points on the ground. A crest may hide part of a mower before the operator loses sight of the whole machine. Long grass, drainage features and changes in grade can also hide a cutting edge or a person approaching the work area.

At a ski resort, map crossings, lift infrastructure and the summer routes used by site staff. Identify the parts of the slope where sightlines change as the machine approaches or leaves a crest. The MERI ski resort slope mowing page provides a starting point for defining the areas the supplier should assess.

Point to checkWhat to recordDecision to make
Approach to the crestFirst point where the head or ground ahead becomes hiddenWhere the planned pass must end
Far side of the crestWork area visible from an approved position on that sideWhether the far side needs its own work zone
Turning pointMachine, cutting head and ground visible during the full turnWhether the turn belongs in the approved route
Operator transitionWalking route, access restrictions and the point where work pausesHow the crew moves between observation positions
Shared approachWhere people or vehicles could enter the areaWhich site controls must be in place during work
Red MERI tracked mower partly obscured by vegetation on a slope
MERI slope demonstration still. Vegetation can obscure parts of the mower, so verify visibility from the approved operator position on your route.

Ask for a visibility check on the offered machine

Identify the exact mower and fitted head in the request. Ask the supplier to show the machine outline and the relevant parts of the cutting assembly in the positions it will use on the route. A change of head can change what the operator needs to see, particularly at a turn near the crest. Ask how the manufacturer specifies operator visibility and which site conditions the demonstrator needs to review before agreeing to the trial.

Record where the operator can see the machine, the cutting area and the part of the route ahead. Ask the site owner and supplier to identify any blind section before the machine approaches it. The MERI site assessment checklist can be used to keep this map with the access measurements, terrain conditions and work requirements. Read the MERI slope mowing safety guide for the broader checks that belong in the operating plan.

Check the route in both directions

Agree on the trial area and stop points with the site owner and supplier. Use the manufacturer's instructions and the approved site method. Have the supplier show the approach and return, since the crest can hide different parts of the route depending on direction. Ask the observer to note the last point where the required view is available. Record the operator position and the machine location on the same sketch. Use a safely staged machine or a marker when the team needs to represent a location beyond the approved pass.

If the crew proposes to cover both sides from different positions, document the route between those positions and the procedure for pausing work while the operator moves. Include the added time in the work plan. Where the route changes direction or has several inclines, use the MERI slope rating guide to record the terrain information the supplier needs. Keep the sightline decision and terrain approval together in the trial record.

Questions to settle before ordering

Is a visible antenna or upper panel enough to approve the pass? Ask the supplier and site team to define the required view for the work. Check that view from the actual operator position throughout the proposed maneuver.

What if the grass is short on the day of the trial? Record the vegetation height and show the supplier how the site looks later in the season. Ask the site manager when growth or another change in conditions triggers a new review.

Can two observation points cover the same slope? Map the ground visible from each approved position and agree where each pass ends. Record the work pause and the path the operator uses to move between them.

Need a mower recommendation for your terrain or project?

Get a Quote
Get a Quote