ME1200-48 for Earth Dam Faces: Mowing Long, Steep Embankments — remote control lawn mower article

Short answer: The ME1200-48 suits long, open earth dam faces where grass must be kept short enough for inspection. Its 1,200 mm flail deck is the widest in the MERI 48 V gasoline range, the product page lists a 45° slope rating, and the operator controls it from the crest or toe. Always follow the dam owner’s inspection and safety rules.

Why dam faces need regular mowing

Earth dam and reservoir embankments are usually kept under short grass. Short grass protects the surface from erosion and lets inspectors see cracks, wet patches, slumps and animal burrows. Long grass and scrub hide those signs.

The trouble is the slope. Dam faces are long and steep, and the people who mow them by hand or with tractor arms face real risk. A remote tracked mower lets the operator stay on the crest road or a berm while the machine works the face.

ME1200-48 product page figures

ItemProduct page figure
EngineLONCIN 459 gasoline, 18 HP
Cutting width1,200 mm
Control system48 V
Electric power2,000 W
Blades48 (flail)
Cutting height30–300 mm (adjustable)
Max slope45°
Remote range800 m
Travel speed0–5 km/h
Fuel tank5.5 L
Weight445 kg
Dimensions (L×W×H)1750×1350×920 mm
Listed working efficiency6,000 m²/hour

Data from the live MERI product page. Confirm the order configuration with MERI before you buy.

Why the wide deck suits dam faces

Dam faces are long, open and mostly free of obstacles. That is where a wide deck pays off. Each pass of the ME1200-48 covers 1,200 mm, so fewer passes are needed per hectare than with an 800 mm machine. The product page lists 6,000 m² per hour as the working efficiency figure.

The trade-off is size. The machine is 1350 mm wide and 445 kg. Check access gates, crest roads and ramps before the first visit.

MERI ME1200-48 gasoline remote control flail mower, front view
Front view of the MERI ME1200-48. The 1,200 mm flail deck covers a wide strip on each pass across an open embankment.

Planning passes across the face

  • Divide the face into sections between access points, berms or drainage channels.
  • Work across the slope in overlapping passes, starting at the top.
  • Keep a steady, slow speed on the steepest section.
  • Leave a safe margin from spillways, outlet structures and wet seepage zones.
  • Note any defect you see while mowing and report it to the dam owner.

Do not mow over seepage areas or soft ground. Mark them and leave them for the inspector.

Inspection-friendly cutting

Agree a target grass height with the dam owner. The deck adjusts from 30 to 300 mm. A consistent, even cut makes later inspection easier. Flail blades mulch the grass and drop it, so there is no thick swath to hide the surface.

Many owners want a cut before each scheduled inspection. Plan your visit a few days before, and photograph the face after mowing for the record.

A worked example

A small reservoir embankment is 400 m long with a 20 m slope length on the upstream and downstream faces: about 16,000 m² in total. At the listed 6,000 m² per hour that is under three hours of cutting on paper. Turns, section changes and refuelling add time, so plan a full day and log the real figure.

Records for the dam owner

Dam owners keep inspection records, and mowing is part of them. After each visit, note the date, the sections cut, the cutting height and anything you saw: wet patches, cracks, slumps, burrows or damaged drains. Add photos of each section from the same points every time. Over a few years these photos show slow changes in the face that an inspector may want to look at. Send the record to the owner with each invoice so it lands in the dam file.

Site rules to follow

  • Follow the dam owner’s permit, access and lone-working rules.
  • Keep clear of the water edge on the upstream face.
  • Check the weather; do not mow wet faces.
  • Keep spectators and anglers out of the work area.
  • Carry the machine’s recovery plan if it stops on the face.

Related MERI pages

Frequently asked questions

Is the ME1200-48 suitable for very steep dam faces?

The product page lists a 45° maximum slope. Most dam faces are less steep, but wet grass and seepage reduce grip. Judge each face on the day.

What engine does the ME1200-48 use?

The product page lists a LONCIN 459 gasoline engine, 18 HP, with a 48 V electric control system.

Can it cut grass short enough for inspection?

The flail deck adjusts from 30 to 300 mm. Agree the target height with the dam owner.

How much area can it cover per hour?

The product page lists 6,000 m² per hour. Real rates on long faces with turns are lower, so log your own figure.

Send us your site details

Tell us the job, area, slope and country. MERI replies within 24 hours.

Ask MERI

Need a mower recommendation for your terrain or project?

Get a Quote
Get a Quote